- intuitive to use
- continuously adjustable color temperature and switch between standard color temperatures (daylight / tungsten)
- brightness regulation 0-100 %
- display the current color temperature in Kelvin, brightness in % and voltage of battery in Volts
- non-volatile user memory
- supply of low cost and available NP-F batteries, or optional other camera batteries
- high efficiency
- low operating temperature
- aluminum casing
- high shock and humidity resistance
DL3120 LED panel emits maximum light output in excess of 5000 lumens. It was designed in dual balance technology, based on a new, flat SMD LEDs with high power and high color rendering. The adjustment of color temperature and brightness of the light are controlled by the microprocessor driver, which gives you extraordinary opportunities. In addition to brightness adjustment they are available two standard color temperatures: daylight and tungsten. You can also manually adjust the color temperature in 3100-5650K range and save the current settings in non-volatile flash memory. A special feature of the controller is a simple and intuitive interface.
It emits a very strong and very wide stream of soft light high quality, completely free from flicker. The angle of light amounts to 120 degrees which allows illuminate large areas from relatively small distance.
The panel allows you to adjust brightness practically with no change in color temperature. It's a great tool to work both on a film set as in the studio. Optional DMX512 controller allows remote control in television studios or when the lamp is placed in hard to reach places.
The control panel is located In the back of DL3120 and consist of the control buttons, a display indicating the current brightness setting in percent and the current color temperature in Kelvin, LEDs signaling the mode of light, the sockets for battery (NP-F type as a standard, available other types of sockets as an options) and socket for AC adapter.
Non-volatile memory can store three settings of panel (brightness and color temperature). To recall the settings from memory, press one of the memory buttons. To save the current settings to memory, hold the selected memory button longer. Memory usage is indicated by the lights on the buttons.
The memory controller also saves the current state of the panel and restores it after turning on the fixture (using the ON/OFF button) or after power loss.
Operating with batteries
Unusual functionality of the DL3120 stems from the possibility of power supply from the popular camcorder batteries NP-F type. The panel requires a two NP-F batteries at the same time. A set of two batteries is able to power the DL3120 at full power up to 1.5 h . There are also other types of adapters for camcorder battery. It gives the opportunity to use the DL3120 with camera batteries of all the leading manufacturers. The list of available adapters can be found here. There are also available adapters to power the light from the batteries of large camcorders V-Mount or Gold Mount.
The controller is equipped with a tester of state of the battery charge. To check the battery charge, press BATT. TEST. The display shows the current battery voltage - upper display indicates the voltage battery installed into the left slot, the lower display indicates the voltage battery installed into the right slot or the voltage of V-Mount/Gold-Mount battery or AC adaptor. Voltage value is displayed with an accuracy to 0.1 V.
The DL3120 is equipped with a standard desktop power supply. AC adaptor allows the continuous work of the light from a 230V as well as 110V. The removable power cord is equipped in an European plug. To use the DL3120 in countries without the European standards, AC adapter should be provided with a suitable cable or adapter. The power supply connector is manufactured by a reputable company and its professional metal construction provides the long-term reliability. The connector is equipped with a threaded bushing, and protects the cable against accidental disconnection.
The DL3120 light is equipped with a mounting yoke made ??of aluminum profiles. The yoke allows you to adjust the position of the light in two axes. To locking the fixture in a vertical axis we use convenient adjustable levers. The yoke is equipped in the typical 5/8F adapter to control and locking the light in horizontal axis and to mount the light to the stand. If you use the light on a floor stand, the angled head allows you to set the yoke at any angle. In addition It is possible mounting a diffusing umbrella to the head. The low weight of the DL3120 enables setting it on the slight stands as Nano.